Contech-lighting TMCFP Manuel d'utilisateur télécharger pdf

IMPORTANT SAFETY INSTRUCTIONS:



Read all instructions before installation. Save these instructions for later use.



TURN OFF THE POWER AT THE FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLA-

TION AND ANY MAINTENANCE.



Wear rubber-soled shoes and work on a sturdy wooden or other non-conductive ladder.



Pendants must be installed according to National Electrical Code and Local Building Codes.

For indoor use only.



To avoid a hazard to children, account for all parts and destroy all packing materials.



WARNING: Risk of ﬁre. Most dwellings built before 1985 have supply wire rated at 60° C.

Consult a qualiﬁed electrician before installation.



Call the Technical Assistance Department at Con-Tech Lighting if you have any installation

questions. 847.559.5500



DO NOT install any pendants closer than 6” from any curtain or similar combustible material.

TMCFP Pendant Assembly Instructions

With the included Allen wrench, loosen the screw in the strain relief near the

socket. Unscrew the strain relief from the threaded nipple and slide it off the cable.

2. Slide one (1) metal and one (1) silicone washer off the cable.

3. Insert the cable into the bottom of the selected glass and slide the glass so it

sits on the silicone washer near the socket.

Reinstall the top two (2) washers and strain relief so they sit on the top of the glass.

5. Screw the strain relief back onto the threaded nipple and tighten the Allen screw.

a. Due to different glass thicknesses, there is a nut to adjust the height of the

washers to achieve a snug ﬁt between the strain relief, washers and glass.

6. Unscrew the strain relief plate at the bottom of the ballast housing to expose the

ballast wires.

7. Run the cable through the ballast housing strain relief plate to connect the

socket wiring to the ballast using the wiring diagram below.

8. Tighten the strain relief plate with the included Allen wrench

9. Screw the strain relief plate back onto the ballast housing.

10. Track polarity is indicated by a grooved polarity line that runs the entire length of

the track.

11. Install the pendant into the track so the arrow on the ﬁxture tab points to the

polarity line when it is rotated into place.

12. Insert the correct lamp per product identiﬁcation label.

ASSEMBLY AND HEIGHT ADJUSTMENT INSTRUCTIONS

For the Con-Tech Lighting Track Mount Compact Fluorescent Pendants (TMCFP series)

Adjustment nut positioned

for thick-topped glass

13W/18W/26W

Adjustment nut positioned

for thin-topped glass

Strain Relief

Metal Washers

Adjustment Nut

Socket

Glass seats between the two sets of washers

Silicone

Washers

Continued

Completed Assembly

www.con-techlighting.com1-847-559-5500 TMCFP INST

All speciﬁcations subject to change without notice.

BLACK

WHITE

Track Head Installation

Fixture

Tab

Arrows

Polarity Line

1 2

Résumé du contenu

Page 1

IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use. TURN OFF THE POWER AT THE FUSE OR C

Page 2

TMCFP Pendant Height Adjustment 1. Unscrew the strain relief plate at the bottom of the ballast housing. 2. Disconnect the ballast from the pendant

Commentaires sur ces manuels

Pas de commentaire

Contech-lighting TMCFP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Contech-lighting TMCFP. ConTech Lighting TMCFP User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Contech-lighting TMCFP